0 item(s) - 0.00 €
Amount (net) | 0.00 € |
VAT | 0.00 € |
Total Amount (gross) | 0.00 € |
The Interface Holders looked good on the wall and they are very convenient too. You don’t have to drill a large hole onto your sauna or steam room wall when using a holder. As the control unit can be easily removed from the wooden mounting, it’s also highly recommended in case of maintenance work is needed. Specify the model or name of your control in which your inferface holders be used.
The Interface Holders looked good on the wall and they are very convenient too. You don’t have to drill a large hole onto your sauna or steam room wall when using a holder. As the control unit can be easily removed from the wooden mounting, it’s also highly recommended in case of maintenance work is needed. Specify the model or name of your control in which your inferface holders be used.
Bench Sensor (2nd reading) suitable for Sawo INNOVA Control Panels types:
Includes Temperature Sensing Thermistor, to assist in more accurate reading of temperature in large and/or irregular shaped saunas.
Sensor Assembly suitable for Sawo INNOVA Control Panels types:
Includes Temperature Sensing Thermistor and Overheat Protection Thermal Fuse ready fitted.
Installation instructions for the surface installation casing
The casing is made of untreated aspen and can be stained, varnished or painted. The casing has a hole for connecting cables at the bottom. If necessary, you can make a hole for the cable in another place using an 8 mm drill bit, for example.
1. Attach the casing with two (2) screws
2. Remove the embedding fl ange. Please note: embedding fl anges
are not used with surface installation casings
3. Spread the glue on the gluing area in the outermost indentation
4. Bring the connecting cable out of the casing and press the heater control unit into position in the casing
5. Remove any excess glue using a cloth moistened with washing-up liquid.
The glue takes 24 hours to dry
Humidity Sensor Assembly suitable for Sawo INNOVA Combi Control Panels type:
Real Time Humidity sensor for Combi Sauna Steamer units MNC + SCAC Types.
Contactor unit for Sawo heaters with power output from 15 to 30 kW.
If the heater used is more than 15 kW, an additional contactor is needed. The contactor unit is linked to the main Power Controller Board, which is included in every set of SAWO Innova control panel, with a low voltage Rj 12 cable.
The Interface Holders looked good on the wall and they are very convenient too. You don’t have to drill a large hole onto your sauna or steam room wall when using a holder. As the control unit can be easily removed from the wooden mounting, it’s also highly recommended in case of maintenance work is needed. Specify the model or name of your control in which your inferface holders be used.
The Interface Holders looked good on the wall and they are very convenient too. You don’t have to drill a large hole onto your sauna or steam room wall when using a holder. As the control unit can be easily removed from the wooden mounting, it’s also highly recommended in case of maintenance work is needed. Specify the model or name of your control in which your inferface holders be used.
Bench Sensor (2nd reading) suitable for Sawo INNOVA Control Panels types:
Includes Temperature Sensing Thermistor, to assist in more accurate reading of temperature in large and/or irregular shaped saunas.
Sensor Assembly suitable for Sawo INNOVA Control Panels types:
Includes Temperature Sensing Thermistor and Overheat Protection Thermal Fuse ready fitted.
Installation instructions for the surface installation casing
The casing is made of untreated aspen and can be stained, varnished or painted. The casing has a hole for connecting cables at the bottom. If necessary, you can make a hole for the cable in another place using an 8 mm drill bit, for example.
1. Attach the casing with two (2) screws
2. Remove the embedding fl ange. Please note: embedding fl anges
are not used with surface installation casings
3. Spread the glue on the gluing area in the outermost indentation
4. Bring the connecting cable out of the casing and press the heater control unit into position in the casing
5. Remove any excess glue using a cloth moistened with washing-up liquid.
The glue takes 24 hours to dry
Humidity Sensor Assembly suitable for Sawo INNOVA Combi Control Panels type:
Real Time Humidity sensor for Combi Sauna Steamer units MNC + SCAC Types.
Contactor unit for Sawo heaters with power output from 15 to 30 kW.
If the heater used is more than 15 kW, an additional contactor is needed. The contactor unit is linked to the main Power Controller Board, which is included in every set of SAWO Innova control panel, with a low voltage Rj 12 cable.